Neugeräte

For better separation in preparative Liquid ChromatographyEach parameter in the analytical LC is set and monitoredvery precisely. The temperature of the column is anessential factor for a good separation and is adjusteddepending on the problem and analytes. In the preparativefield, temperature control for columns has been thought of,but columns are only heated externally. For low flow ratesin the analytical field this might be sufficient, but forpreparative separations and high flow rates a lot ofefficiency is lost when the mobile phase is not heated.Lower mobile phase viscosityFaster interaction with stationary phaseLower system back pressureHigher flowrates without loosing resolutionShorter cycle timesEqualize the enthalpy of mixing solvents Columns1 columnup to 50x250mm)ControlIntegrated Keyboard control, PC direct control Column selection Valve8-Pos. Max Pressure: 5000psiOutputsError signal contact closure Flowrate200ml/minInputsBCD-/Impulse Signal for Column position Max. Pressure400bar1/16" SS-Tubing Heat ExchangerDimensions (WxHxD)35x61x28 cm Temperature Range5 - 55 °C (in 0.5 °C increments)Weight27 kg Accuracy0.1 °CEnviromental Conditions5 - 40 °C, 35 - 75% rH ReproducibilityBetter than 0.5 °CPower Requirements115/230 VAC; 50/60 Hz StabilityBetter than 0.5 °CMax. power Consumption1520 VA SensorsSolvent Vapor alarm, Leakage alarm, Temperature warning

Price on request

ECODRY 65 plus (refurbished) - Mehrstufige Wälzkolbenpumpe

New instrumentTechnische Daten:Max. Saugvermögen ohne Gasballast: 55 m³/hEnddruck ohne Gasballast: 3 x 10-2 mbarLeckrate: < 1E-5 mbar l/sWasserdampfkapazität (mit Gasballast): 500 g/hSchalldruckpegel bei Enddruck: 52 dB(A)Gewicht: 43 kgAbmessungen (BxLxH): 320 x 623 x 298 mm³Schutzart: IP 42Ansaugflansch: DN40 ISO-KFAuslassflansch: DN16 ISO-KFKühlung: Luft

Price on request

FLOM Attachment Panel for V200 Series, SS

The valve shown in the picture is not included in the scope of delivery and must be ordered separately from the list shown below. Product NumberFL-V200FL-V201FL-V204FL-V512FL-V239FL-V05 Type6 port 2 position3 port 2 way2 port selection6 port 2 position Max Pressure20MPa (2900psi)30MPa (4350psi)1MPa (145psi)35 Mpa (5800 psi) Wetted MaterialsPEEKSUS, PEEKPEEKSUS, PEEK Tube OD1/16"ø3, 1/8"1/16" Path Diameter0.6mm (0.024")0.8mm (0.03")0.8mm (0.03")1.0mm (0.04")0.6 mm Thread SizeNo.10-32UNF1/4-28UNFNo.10-32UNF

€75.00*

FLOM Auto Back Pressure Regulator, STEEL, 100 mL/min., 5MPa (725 psi)

Material: SS

FeaturesProvide consistent pressure by tracking variable pump pressure in real timeUI Series provides stable flow, BP-11 maintains set pressure Product NameAuto Backpressure Regulator BP-11 Series Product No.BP-11SBP-11D Wetted materialsSUS316Teflon (PCTFE) Max Pressure5 Mpa (725 psi) Max Flow Rate100 mL/min. Path Diameter0.6 mm Setup Pressure Range0.10 - 5.00 MPa (14.5 - 725 psi) Pressure Signal RangeUses pressure signal from UI / MP pumps [ DC1 - 5V ] Pressure Accuracy± 0.1 MPa (± 14.5 psi) FeaturesManual mode, Auto-stop Remote controlInput: Start / Stop, Output: FUNC RS232C , RS485 (between FLOM devices) Dimensions144 (H) × 79 (W) × 240 (D) mm , excluding protuberances Weight Approx. 2.7 kg Power AC1000 - 240V (50 / 60 Hz) , MAX 70 VA

€3,200.00*

FLOM Auto valve unit

Path diameter: 0.25 mm (0.01”) | Port: 6-port | Material: SUS, PEEK | Max. Pressure: 40 MPa / 5800 psi

For general, high speed, and fraction analysis, choose the flow paths you need to cover a wide variety of applicationsFeaturesPath diameter 0.15 mm as thinner-bore availableFor UHPLC applications, maximum pressure 140 MPa (20305 psi) addedPick the valve type that fits your applicationFeaturing high flow and non-metallic typesLong valve life based on FLOM technologyPlease note: For the new pump heads FL-21-628, FL-21-629, and FL-21-630, the price is only available upon request from Fischer Analytics.Delivery time for all items listed in the table is 5–6 weeks from receipt of the order by Fischer Analytics. Product no.TypeMax PressureWetted MaterialTube ODThread SizePath Diameter FL-VA-21-6016 Port, 2 position40 MPa (5800 psi)SUS, PEEK1/16”No.10-32UNF0.25 mm (0.01”) FL-VA-21-60230 MPa (4350 psi)PEEK, Ceramic FL-VA-21-60340 MPa (5800 psi)SUS, PEEK0.5 mm (0.02”) FL-VA-21-60430 MPa (4350 psi)PEEK, Ceramic FL-VA-21-60520 MPa (2900 psi)SUS, PEEK1.0 mm (0.04”) FL-VA-21-606PEEK, Ceramic FL-VA-21-6075 MPa (725 psi)SUS, PEEK3.0 mm or 1/8”M8×1.252 mm (0.079”) FL-VA-21-608PEEK, Ceramic FL-VA-21-6094 Port, 2 position40 MPa (5800 psi)SUS, PEEK1/16”No.10-32UNF0.5 mm (0.02”) FL-VA-21-61030 MPa (4350 psi)PEEK, Ceramic FL-VA-21-6112 Port, selection40 MPa (5800 psi)SUS, PEEK FL-VA-21-61230 MPa (4350 psi)PEEK, Ceramic FL-VA-21-6135 MPa (725 psi)SUS, PEEK3.0 mm or 1/8”M8×1,252 mm (0.079”) FL-VA-21-614PEEK, Ceramic FL-VA-21-6154 Port, rotary40 MPa (5800 psi)SUS, PEEK1/16”No.10-32UNF0.5 mm (0.02”) FL-VA-21-61630 MPa (4350 psi)PEEK, Ceramic FL-VA-21-6176 Port, rotary40 MPa (5800 psi)SUS, PEEK FL-VA-21-61830 MPa (4350 psi)PEEK, Ceramic FL-VA-21-6195 MPa (725 psi)SUS, PEEK3.0 mm or 1/8”M8×1.252 mm (0.079”) FL-VA-21-620PEEK, Ceramic FL-VA-21-62112 Port, rotary20 MPa (2900 psi)SUS, PEEK1/16”No.10-32UNF0.5 mm (0.02”) FL-VA-21-622PEEK, Ceramic FL-VA-21-6238 Port, 2 positionSUS, PEEK FL-VA-21-6248 Port, rotarySUS, PEEK FL-VA-21-62712 Port, 2 positionSUS, PEEK0.25 mm (0.01”) FL-VA-21-6286 Port, 2 position40 MPa (5800 psi)SUS, PEEK0.15 mm (0.006”) FL-VA-21-629140 MPa (20305 psi)SUS FL-VA-21-630SUS0.25 mm (0.010”) For the new pump heads FL-21-628, FL-21-629, and FL-21-630, the price is available only upon request from Fischer Analytics.

Variants from €1,550.00*

€1,900.00*

FLOM Gastorr AG Series 2 Channels Degasser, Teflon AF

Kanäle: 2

Redesigned high precision degassing unit with improved self-cleaning functionFeatures • Uses Teflon™AF tubing for minimal internal volume • Self-cleaning function protects device interior • CPU control achieves stable degassing • Independent chamber design prevents solvent contamination • Choose from 2 channel or 4 channel configurations Model numberFL-AG-42-01FL-AG-44-01FL-BG-42-02FL-BG-44-02FL-BG-42-10FL-BG-44-10FL-FG-42FL-PG-41PFL-PG-42P Channels242424212 Internal volume340 µL510 µL1020 µL10 ml62.0ml Flow rate≤ 10 mL/min≦ 10 mL/min≦ 5mL/min≦50.0mL/min Vacuum range100 hPa fixed150 hPa fixed Thread size1/4-28 UNF Wetted materialTeflon TM AF*1, ETFE, PTFE PTFE , ETFE , PPSPTFE , ETFE , PEEK Remote control-Input: - Output: Error signal Dimensions108 (H) × 70 (B) × 240 (T) mm, excluding protuberances180(H) ×90(W) × 400(D) mm, excluding protuberances Weightapprox. 2.1 kgapprox. 2.3 kgapprox. 5.0 kgapprox. 6.0 kg PowerAC 100 - 240 V (50 / 60 Hz) MAX 80 VA *1:Teflon TM AF is a registered trademark of the Chemours Corporation.Note: cannot be used with fluorinated solvents.

€1,500.00*

FLOM Gastorr FG Series, PTFE, 2 channel, 10mL, 100 hPa (fixed)

Solvent Degassing SystemDegassing system for fluorinated solventsFeaturesDesigned for use with fluorinated solventsAuto cleaning function prevents vacuum pump deteriorationCPU control achieves stable degassingReal time display of vacuum levelIndependent chamber design prevents solvent contamination Model numberFL-AG-42-01FL-AG-44-01FL-BG-42-02FL-BG-44-02FL-BG-42-10FL-BG-44-10FL-FG-42FL-PG-41PFL-PG-42P Channels242424212 Internal volume340 µL510 µL1020 µL10 ml62.0ml Flow rate≤ 10 mL/min≦ 10 mL/min≦ 5mL/min≦50.0mL/min Vacuum range100 hPa fixed150 hPa fixed Thread size1/4-28 UNF Wetted materialTeflon TM AF*1, ETFE, PTFE PTFE , ETFE , PPSPTFE , ETFE , PEEK Remote control-Input: - Output: Error signal Dimensions108 (H) × 70 (B) × 240 (T) mm, excluding protuberances180(H) ×90(W) × 400(D) mm, excluding protuberances Weightapprox. 2.1 kgapprox. 2.3 kgapprox. 5.0 kgapprox. 6.0 kg PowerAC 100 - 240 V (50 / 60 Hz) MAX 80 VA

€2,050.00*

FLOM Gastorr PG Series, PTFE, 1 Channel, 62.0 mL, 150 hPa (fixed)

Kanäle: 1

Features• Flow rates up to a max of 50 mL/min• Auto cleaning function prevents vacuum pump deterioration• CPU control achieves stable degassing• Real time display of vacuum level• Independent chamber design prevents solvent contamination• Choose from 1 channel or 2 channel configurations Model numberFL-AG-42-01FL-AG-44-01FL-BG-42-02FL-BG-44-02FL-BG-42-10FL-BG-44-10FL-FG-42FL-PG-41PFL-PG-42P Channels242424212 Internal volume340 µL510 µL1020 µL10 ml62.0ml Flow rate≤ 10 mL/min≦ 10 mL/min≦ 5mL/min≦50.0mL/min Vacuum range100 hPa fixed150 hPa fixed Thread size1/4-28 UNF Wetted materialTeflon TM AF*1, ETFE, PTFE PTFE , ETFE , PPSPTFE , ETFE , PEEK Remote control-Input: - Output: Error signal Dimensions108 (H) × 70 (B) × 240 (T) mm, excluding protuberances180(H) ×90(W) × 400(D) mm, excluding protuberances Weightapprox. 2.1 kgapprox. 2.3 kgapprox. 5.0 kgapprox. 6.0 kg PowerAC 100 - 240 V (50 / 60 Hz) MAX 80 VA

€3,000.00*

FLOM Hex Fitt Mini Medium Pressure Fittings, PEEK, (10-pack)

Product No.Product NameSpecificationsUnits/pck MaterialTubing SizeThread SizeMax. Pressure FL-9620Dual-Fitt SETSUS316/PEEKOD 1/16"No.10-32UNF140 Mpa (20.300 psi)10 FL-9621Dual-FittingSUS316OD 1/16"No.10-32UNF10 FL-9623-05Replacement FerruleSUS316/PEEKOD 1/16"-5 FL-9623-10Replacement FerruleSUS316/PEEKOD 1/16"-10 FL-95011/16" Fitting SSUS316OD 1/16"No.10-32UNF40 Mpa (5.800 psi)10 FL-95021/16" Fitting LSUS316OD 1/16"No.10-32UNF10 FL-96011/16" FerruleSUS316OD 1/16"-10 FL-9935S1/16" Single Lock Fitting SSUS316/PEEKOD 1/16"No.10-32UNF50 Mpa (7.250 psi)10 FL-9935P1/16" Single Lock Fitting PPEEKOD 1/16"No.10-32UNF40 Mpa (5.800 psi)10 FL-9001Easy Fitt OD 10 mmPEEKOD 1/16"No.10-32UNF20 Mpa (2.900 psi)10 FL-9002Easy Fitt OD 12 mmPEEKOD 1/16"No.10-32UNF10 FL-9130Easy Fitt Type 2PEEKOD 1/16"No.10-32UNF10 FL-9004Stop FittPEEKOD 1/16"No.10-32UNF10 FL-9003Hex FittPEEKOD 1/16"No.10-32UNF40 Mpa (5.800 psi)10 FL-9135Hex Fitt MiniPEEKOD 1/16"No.10-32UNF10

€50.00*

FLOM Injector Panel, SS

The valve shown in the picture is not included and must be purchased separately from the list below.It cannot be attached to FLOM pumps. Product NumberFL-V200FL-V201FL-V204FL-V512FL-V239FL-V05 Type6 port 2 position3 port 2 way2 port selection6 port 2 position Max Pressure20MPa (2900psi)30MPa (4350psi)1MPa (145psi)35 Mpa (5800 psi) Wetted MaterialsPEEKSUS, PEEKPEEKSUS, PEEK Tube OD1/16"ø3, 1/8"1/16" Path Diameter0.6mm (0.024")0.8mm (0.03")0.8mm (0.03")1.0mm (0.04")0.6 mm Thread SizeNo.10-32UNF1/4-28UNFNo.10-32UNF

€75.00*

FLOM Intelligent Micro pump

Intelligent Micro Pump MP-22Valve Switching Micro PumpCheck valve-less design for super low pulse control under low flow ratesFeaturesImproved near-zero pulse flowProblems with bubble greatly reducedEasy setupUpper and lower pressure limitersSpace-saving compact designExternal control available with RS232C protocol Part numberMP-22-110S Pumphead materialSUS Max pressure*35 MPa (5075 psi) Flow rate range**0.001 - 9.999 mL/min Flow per stroke80 µL Plunger stroke10 mm Flow accuracy***< 0.3 % FeaturesActive pulse reduction, upper/lower pressure limiters Pressure accuracy< 5 % Wetted materialsSapphire, Ruby, PTFE, PCTFE, PFA, ETFE, FFKM, HDPE, PEEK, SUS Remote controlInput:PUMP ON / OFF, Output:Error signal CommunicationRS232C, RS485(between FLOM devices) Dimensions150 (H) ×, 160 (W) ×, 280 (D) mm, excluding protuberances WeightApprox. 6.7 kg PowerAC100 - 240 V (50 / 60 Hz) MAX 140 VA *: Maximum pressure is only sustained intermittently.**: Maximum output is not sustainable over long periods of time.***: Using Methanol at flow rate10~500&mu,L/min , output pressure >, 1 MPa ~ 20MPa

€7,900.00*

FLOM Intelligent pump PEEK 80 μL is replaced bys UI-32 series

Material: PEEK | Max. Flow Rate: 10 mL/min. | Max. Pressure: 20 MPa / 2900 psi

This intelligent pump of the UI-22 series is now being replaced by the intelligent pump of the UI-32 series. However, spare parts for the UI-22 series are still available.FeaturesPulses reduced to absolute minimum making low flow rate pumping possibleBubble problems greatly reducedLong life plunger sealUpper and lower pressure limitersSpace-saving compact designControl with RS232C protocolChoose SUS, PEEK, or PCTFE to fit your solvent Part numberUI-22-110SUI-22-110PUI-22-110DUI-22-410SUI-22-410PUI-22-410D Pumphead materialSUSPEEKPCTFESUSPEEKPCTFE Max pressure*35 MPa (5075 psi)20 MPa (2900 psi)2 MPa (290 psi)5 MPa (725 psi)5 MPa (725 psi)2 MPa (290 psi) Flow rate range**0.001 - 9.999 mL/min0.01 - 99.99 mL/min Flow per stroke80 μL708 μL Plunger stroke10 mm Flow accuracy<, 0.3 % FeaturesActive pulse reduction, upper/lower pressure limiters Pressure accuracy<, 5 % Wetted materialsSUS: Sapphire, Ruby, PTFE, PCTFE, PFA, FFKM, HDPE, PEEK, SUS PEEK: Sapphire, Ruby, PTFE, PCTFE, PFA, ETFE, FFKM, HDPE, PEEK PCTFE: Sapphire, Ruby, PTFE, PCTFE, PFA, ETFE, FFKM Remote controlInput:PUMP ON / OFF, Output:Error signal CommunicationRS232C , RS485(between FLOM devices) Dimensions144 (H) × 105 (W) × 240 (D) mm, excluding protuberances WeightApprox. 5.6 kg PowerAC100 - 240 V(50 / 60 Hz) MAX140 VA *: Maximum pressure is only sustained intermittently.**: Maximum output is not sustainable over long periods of time.

€4,300.00*

FLOM Low Pressure Damper, PEEK/FEP, 2 MPa (290 psi)

Features Product NameHigh Pressure DamperMedium Pressure DamperLow Pressure Damper Product NumberFL-9810FL-9805FL-9800 Max Pressure20MPa10MPa2MPa Pulse Control Range8～12MPa0.5 ～ 5 MPa0.1～0.7MPa Internal Volumemax.3.5mlmax. 0.8 mL Wetted MaterialsPEEK, PTFEPEEK, FEP Port TypeNo.10-32UNF DimensionsDiameter 50mm × Length 36.5mmDiameter 45mm × Length 150mmDiameter 45mm × Length 33mm Weightmax.0.3kg

€540.00*

FLOM Manual Sample Injector , SUS 316/PEEK/Ceramic, 35 MPa (5075 psi)

Features• Ultra high-pressure spec allows sample injection into high pressure fluid pathways• Ultra high precision minimizes sample loss• Can output injection marker Product nameManual Sample Injector Part NumberFL-VI-11FL-VI-12FL-MI-11 Wetted MaterialsSUS, PEEK, CeramicCeramic, PEEKSUS, PEEK, Ceramic Max Pressure35MPa (5075psi)100 MPa (14,500psi) Tube OD1/16" Path Diameter0.5mm(0.02")0.25 mm (0.01”) Port TypeNo.10-32UNF Sample Loop (Standard)20μl (SUS)20μl (PEEK)5 μL (SUS) Injection MarkerBuilt-in (1.5 m Lead Wire) Matching sample loops are also available from us under the following item numbers: SS Sample Loop PEEK Sample Loop Product no.Sample size Product no.Sample size FL-7511S10μl FL-7511P10μl FL-7112S20μl FL-7512P20μl FL-7513S50μl FL-7513P50μl FL-7514S100μl FL-7514P100μl FL-7515S200μl FL-7515P200μl FL-7516S500μl FL-7516P500μl FL-7517S1ml FL-7517P1ml

€625.00*

FLOM Manual Sample Injector Ceramic/PEEK, 35 MPa (5075 psi)

€700.00*

FLOM Manual Valve, 1-2 port rotary, PEEK, 1MPa (145 psi), 3.0 mm or 1/8", 1.0 mm

A convenient, ultra-compact valve for switching flow pathsFeatures• Attach to the valve panel (sold separately) to allow operation from valve head side • A line-up of 5 units to cover a wide variety of applications Product NumberFL-V200FL-V201FL-V204FL-V512FL-V239FL-V05 Type6 port 2 position3 port 2 way2 port selection6 port 2 position Max Pressure20MPa (2900psi)30MPa (4350psi)1MPa (145psi)35 Mpa (5800 psi) Wetted MaterialsPEEKSUS, PEEKPEEKSUS, PEEK Tube OD1/16"ø3, 1/8"1/16" Path Diameter0.6mm (0.024")0.8mm (0.03")0.8mm (0.03")1.0mm (0.04")0.6 mm Thread SizeNo.10-32UNF1/4-28UNFNo.10-32UNF Corresponding side panels for the valves can be ordered under the item numbers shown in the list below: Product NameSide Panel Product NumberFL-4512FL-4513FL-4514 Pump TypeUI Series, MP Series, SP Series, DP-11 Attachable PartsVI-11, VI-12, MI-11,V05V200, V201, V204, V239, V512 Damper Attachableyesnoyes Dimensions144(H)×60(W)×44(D), excluding protuberances

€325.00*

FLOM Manual Valve, 1-2 port rotary, PEEK, 20 MPa (2900 psi), 1/16", 0,8 mm

€190.00*

FLOM Manual Valve, 3 port 2 way, PEEK, 20 MPa (2900 psi), 1/16", 0.6 mm

€240.00*

FLOM Manual Valve, 6 port 2 position, PEEK, 20 MPa (2900 psi), 1/16", 0.6 mm

€240.00*

FLOM Manual Valve, 6 port 2 position, SUS316/PEEK, 35 MPa (5800 psi), 1/16", 0.6 mm

A convenient manual valve for switching between flow paths.FeaturesLow torque design for easy switching Product NumberFL-V200FL-V201FL-V204FL-V512FL-V239FL-V05 Type6 port 2 position3 port 2 way2 port selection6 port 2 position Max Pressure20MPa (2900psi)30MPa (4350psi)1MPa (145psi)35 Mpa (5800 psi) Wetted MaterialsPEEKSUS, PEEKPEEKSUS, PEEK Tube OD1/16"ø3, 1/8"1/16" Path Diameter0.6mm (0.024")0.8mm (0.03")0.8mm (0.03")1.0mm (0.04")0.6 mm Thread SizeNo.10-32UNF1/4-28UNFNo.10-32UNF

€550.00*

FLOM Roller pump, PharMed BPT, 3 ml/Min., 90 kPa (13 psi)

Great for plunger pump cleaning and basic pumping applicationsFeatures:Space-saving compact designTubes can be selected according to the solvent usedTube cassette can be set in four directions Product NameRoller Pump ModelWP-21 Flow rate range4-stage variable (approx. 0.5・1.0・2.0・3.0mL/min) Flow Rate Switching 4-stage via front switch (rotary type) Special Function Purge delivery via long press of front switch (approx. 5mL/min) Flow Accuracy± 5 % (PharMed®BPT*¹ when new) Discharge Pressure 90 kPa or less (PharMed®BPT*¹) Suction Pressure-90 kPa or less (PharMed®BPT*¹) Operating Liquid Temperature Range 5 to 50°C Rotation DirectionClockwise when viewed from front External Input/Output Signals Input: Conductive OFF, Open ON Output: Error output via open collector Tube MaterialPharMed®BPT*¹ / FLURAN F-5500-A / Transmaster TM-15 Dimensions 65 (H) × 46 (W) × 110 (D) mm, excluding protrusions WeightApprox. 0.5 kg Power DC 24 V, MAX 15 W (AC adapter included) *1 “PharMed®BPT” is a registered trademark of Saint-Gobain K.K.* Standard specifications use “PharMed®BPT” tubing. Please inquire if you require “Fulan F-5500-A” or "TransMasterTM-15”. * Turning the power switch ON automatically initiates fluid delivery.

€640.00*

FLOM Sample Loop 5 μL, SS for MI-11

Sample Loop for MI-11 Product no.Sample size FL-7500M5μL

€55.00*

FLOM Side Panel for Valve Attachment for combination of 9800, 9810 & VI-11, VI-12, MI-11, V05

Features Product NameSide Panel Product NumberFL-4512FL-4513FL-4514 Pump TypeUI Series, MP Series, SP Series, DP-11 Attachable PartsVI-11, VI-12, MI-11,V05V200, V201, V204, V239, V512 Damper Attachableyesnoyes Dimensions144(H)×60(W)×44(D), excluding protuberances The valves shown in the picture are not included in the scope of delivery and must be ordered separately under the following article numbers: Product NumberFL-V200FL-V201FL-V204FL-V512FL-V239FL-V05 Type6 port 2 position3 port 2 way2 port selection6 port 2 position Max Pressure20MPa (2900psi)30MPa (4350psi)1MPa (145psi)35 Mpa (5800 psi) Wetted MaterialsPEEKSUS, PEEKPEEKSUS, PEEK Tube OD1/16"ø3, 1/8"1/16" Path Diameter0.6mm (0.024")0.8mm (0.03")0.8mm (0.03")1.0mm (0.04")0.6 mm Thread SizeNo.10-32UNF1/4-28UNFNo.10-32UNF

€150.00*

FLOM Side Panel for Valve Attachment for V200, V201, V204, V239, V512

€150.00*